Teaching myself to ''corner weld'' at home

Outside corner weld job report

Before turning the welder on I made sure that it was in a safe working condition, this involves checking any connections were secure, checking that there was no live wires showing through the cables and checking that the valve on the gas cylinder was secure.
The material that I used for this job was 1.6mm mild steel sheet, I used two pieces of 50x150mm.

The first step in the outside corner weld is to tack weld them into place, this involves making an equal gap along the corner of the two pieces along the length. I placed one tack weld on one end of the material making sure that the gap was the correct size (similar to the thickness of the 1mm filler wire I was using). I placed one tack weld at one end so it would not be so affected by distortion and so that I could easily manipulate the other end to make the gap equal. I then placed a small tack at the other end and I then placed small tack welds (small enough so that they will not be seen after the weld has been complete) with equal distances of around 20mm across the length. For getting the material into place I used a small 50mm jig to place one piece of material up resting against and the other resting on top, by doing this it was easy to manipulate the material to get a suitable gap.

Before final welding I checked that the joint was accurate, this involved checking that the plates were square on the ends and that the gap between the two pieces was equal across the entire length. After I have ensured that the tack welds were accurate and that the material was in the correct place for the type of weld I prepared for the final weld. This involved making sure that I had enough filler wire at hand and that I had a sharp tungsten tip. Once I had made these checks, I then began the weld making sure that the heat from the tungsten was split evenly between the two pieces of material so that there would be significant penetration on each piece of material.

After completing the weld with at least one stop and start, I performed visual inspections on the weld to make sure that the uniformity was to standard. I flipped the material over to make sure that there was visible penetration on the opposite side to the side welded.

Destructive test on the corner weld

Comments

Impacts of a poor customer design process on customer relationships and requirements

The possible impact of a poor customer design process on customer relationships and requirements Poor design process can have serious negative effects on a company relationship with their customers. A common occurrence in business is poor communication between the customer and the business. Poor communication in the customer design process may involve improper consideration of information passed on by the customer, this means the completed product is likely to not be of the standard/specifications requested. This can be caused by lack of technical specification or the company simply not following the technical specification, this is due to the technical specification being the most important part in the design process due to it containing so much vital information. If the technical specification is not used/followed then the end product is very likely to not match the customer’s requirements. A finished product that doesn’t match the customer’s requirements will like...

How 3D CAD models can be used in the design process

How 3D CAD models can be used in the design process ⦁ 3D CAD models can be used to replace the manual drafting processes with a more automated process, it allows you to visualize the design from different angles and analyse the feasibility of its working. By visualizing the design you can easily spot and flag mistakes in it and witness the entire design before it has been manufactured so it removes some of the need for rapid prototyping. ⦁ A wide variety of 3D software can be used for different types of simulation, mechanical design and analysis. Kinematics programs have many different tools which allow you to test the way that a part functions and allows you to see it working before it is manufactured, this can be extremely effective for spotting issues with how the parts function with each other as sometimes there are collisions in moving parts. Some of this software has a tool called the mechanism tool which will automatically tell you if it thinks the parts are not interacting ...

Evaluation on the impact of legislation and standards on design process

Evaluation on the impact of legislation and standards on the design process in relation to the profitability of the business Legislation and standards can impact the profits of companies in many ways, an example of this would be if O-Sep would not follow the health and safety tests on their designs then they may be fined, this would affect the profits of the company. Copyright laws on designs may also affect O-sep, if they were to design an alarm system that is based on an alarm system of another company that is copyrighted then they can be fined large amounts of money. An example of legislation in the design process that impacts the profitability of the business is EN 50131-1. This legislation states that components that are used must be classified safe for the environmental classification and must be given a security grading, this may mean that more expensive components must be used as the components must suit EN 50131-1. The design process may also be...

Engineering at home

Search This Blog